Now that's what I call a productive afternoon. Since my 59.5gr load shot so well in practice, I decided to load up 40 rounds for the Safari Rifle match two Sundays from now (30 March). This will let me save my dwindling supply of factory ammo.
Now, I've loaded almost 60 total rounds of 9.3x62mm, and I was shocked to see that I'm more than halfway through my pound of Big Game. I'm used to loading mild .38 Special and .44 Special, with about 4-4.5gr of powder per cartridge. I've been on the same pound of 700x for a year now, and I'm just barely putting a dent into it. But when you're using almost 60 grains per cartridge, you burn through a pound of powder (7000 grains) in fairly short order. Time to find a big jug!
Showing posts with label Reloading. Show all posts
Showing posts with label Reloading. Show all posts
Saturday, March 15, 2014
Sunday, March 9, 2014
The moment of truth.
Well, it's time for the moment of truth. I shot an IDPA match this morning, and did reasonably well. I shot some follow-up drills and did better. Then I scampered off to the rifle side of the facility to test out my first-ever batch of rifle handloads.
I set up a makeshift rest with the range's carpet-covered wooden blocks and my folded soft case, loaded up the first three rounds (56.5gr of Big Game) and got to work, checking each individual case for pressure signs. Then three rounds with 57.5, three more with 58.5 and so on until I got to 61.5gr. By that time, I had started to develop a bit of a flinch from shooting off the bench, and I decided it would be impractical to continue shooting groups. I fired one round with 62.0gr from the shooting sticks (mostly to verify there were no pressure signs, and there weren't), and banged steel @ 200 yards. I fired five more factory Prvi rounds, but the flinch was starting to show. I buckled down and fired one last round and banged steel. I like to finish on a high note.
Then it was off to the butts to see how I did. And boy, was I surprised. I had a few stringers that I will readily ascribe to the emergent flinch (especially on the last two sets of three), but the 59.5gr load (rounds 10, 11 and 12) shot sub-MOA @ 100 yards!
Now I need to get a chronograph and see how much velocity that load's pushing, and load up some more from about 59gr to 62.5gr and see if that's the sweetest spot or if there are greener pastures.
Now, on to the shooting sticks. Work bit into my free time, so I only had time to craft one set of sticks. I used the green Home Depot garden stakes with a section of bicycle inner tube to make a very simple apparatus. And yet, with a proper hold, I was able to shoot reasonably well @ 200 yards with it. I found that by laying my hand in the crotch of the sticks, and using that to brace the gun and prevent it from bouncing, I could shoot pretty well. I really like these sticks. They're extremely lightweight, stiff, tough, and practical. Best of all, they cost me all of $7 and change. I'm thinking of getting a third stake to try the tripod route, but right now I'm finding it hard to argue with the simple effectiveness of the current setup. Still, experimentation is what this is all about, so I'll give it and the wooden swivel bipod sticks a run for the money.
I set up a makeshift rest with the range's carpet-covered wooden blocks and my folded soft case, loaded up the first three rounds (56.5gr of Big Game) and got to work, checking each individual case for pressure signs. Then three rounds with 57.5, three more with 58.5 and so on until I got to 61.5gr. By that time, I had started to develop a bit of a flinch from shooting off the bench, and I decided it would be impractical to continue shooting groups. I fired one round with 62.0gr from the shooting sticks (mostly to verify there were no pressure signs, and there weren't), and banged steel @ 200 yards. I fired five more factory Prvi rounds, but the flinch was starting to show. I buckled down and fired one last round and banged steel. I like to finish on a high note.
Then it was off to the butts to see how I did. And boy, was I surprised. I had a few stringers that I will readily ascribe to the emergent flinch (especially on the last two sets of three), but the 59.5gr load (rounds 10, 11 and 12) shot sub-MOA @ 100 yards!
Now I need to get a chronograph and see how much velocity that load's pushing, and load up some more from about 59gr to 62.5gr and see if that's the sweetest spot or if there are greener pastures.
Now, on to the shooting sticks. Work bit into my free time, so I only had time to craft one set of sticks. I used the green Home Depot garden stakes with a section of bicycle inner tube to make a very simple apparatus. And yet, with a proper hold, I was able to shoot reasonably well @ 200 yards with it. I found that by laying my hand in the crotch of the sticks, and using that to brace the gun and prevent it from bouncing, I could shoot pretty well. I really like these sticks. They're extremely lightweight, stiff, tough, and practical. Best of all, they cost me all of $7 and change. I'm thinking of getting a third stake to try the tripod route, but right now I'm finding it hard to argue with the simple effectiveness of the current setup. Still, experimentation is what this is all about, so I'll give it and the wooden swivel bipod sticks a run for the money.
Labels:
9.3x62,
Ammo,
cartridges,
guns,
Reloading,
shooting sticks
Monday, March 3, 2014
Reloading... progress!
I was supposed to fly to Dallas yesterday for a training conference, but Mother Nature decided otherwise. To console myself, I ventured into the reloading room to work on my 9.3x62mm loads. I had done a bit of research and talked to some folks who do quite a bit of reloading in this caliber (in addition to some good advice from people reading here), and it made me confident of some of the dimensions I would need. So, off to the loading bench I went.
As commenter "BS" mentioned after my earlier reloading post, I started with a lower charge and worked up. I loaded a few rounds in each charge weight, going up one grain at a time. So now I've got 18 rounds theoretically (see below) ready to test-fire, hopefully next weekend if the weather cooperates (and it's Phoenix in March, so it usually does).
I did find some unusual results. All of my cases are once-fired Prvi Partizan brass. I miked four or five out of the batch to see if I needed to trim, and they were all within a few thousandths of each other, and well within acceptable length. When I loaded them, I got a fairly wide range of COL. Minimum was about 3.295, and max was 3.307. That seemed like a large discrepancy, so I used my bullet puller to tap the projos slightly forward, and reseated them, thinking my seating die might have come loose. They all reseated... to the same COL they were before being pulled. The 3.295 cartridge reseated to 3.295, and the 3.307 cartridge reseated to 3.307. All of them fed and chambered in my rifle with no issues, but it's troubling. There seemed no rhyme or reason to why they were different lengths. I had rounds with the same powder charge near each of the extremes. None of the charges got up into the neck of the case, so I'm not yet dealing with compressed loads. I'm going to start with the lightly-loaded rounds and see if there is any variation in point of impact, recoil, or any signs of pressure. If not, then I'll gradually work up. I didn't load up to the max yet, I can always come back and load them if I see no pressure signs. The next batch I load, I'll mike every case to ensure uniform length, and the projos as well.
The second thing I wish to accomplish before the weekend is to construct a basic set of shooting sticks. I'll shoot groups off sandbags on the bench, of course, but I would also like to shoot some factory ammo from the sticks to refine my technique before the match at the end of the month.
All in all, a day of both frustration and satisfaction. The weekend will determine how it all ends up.
As commenter "BS" mentioned after my earlier reloading post, I started with a lower charge and worked up. I loaded a few rounds in each charge weight, going up one grain at a time. So now I've got 18 rounds theoretically (see below) ready to test-fire, hopefully next weekend if the weather cooperates (and it's Phoenix in March, so it usually does).
I did find some unusual results. All of my cases are once-fired Prvi Partizan brass. I miked four or five out of the batch to see if I needed to trim, and they were all within a few thousandths of each other, and well within acceptable length. When I loaded them, I got a fairly wide range of COL. Minimum was about 3.295, and max was 3.307. That seemed like a large discrepancy, so I used my bullet puller to tap the projos slightly forward, and reseated them, thinking my seating die might have come loose. They all reseated... to the same COL they were before being pulled. The 3.295 cartridge reseated to 3.295, and the 3.307 cartridge reseated to 3.307. All of them fed and chambered in my rifle with no issues, but it's troubling. There seemed no rhyme or reason to why they were different lengths. I had rounds with the same powder charge near each of the extremes. None of the charges got up into the neck of the case, so I'm not yet dealing with compressed loads. I'm going to start with the lightly-loaded rounds and see if there is any variation in point of impact, recoil, or any signs of pressure. If not, then I'll gradually work up. I didn't load up to the max yet, I can always come back and load them if I see no pressure signs. The next batch I load, I'll mike every case to ensure uniform length, and the projos as well.
The second thing I wish to accomplish before the weekend is to construct a basic set of shooting sticks. I'll shoot groups off sandbags on the bench, of course, but I would also like to shoot some factory ammo from the sticks to refine my technique before the match at the end of the month.
All in all, a day of both frustration and satisfaction. The weekend will determine how it all ends up.
Friday, February 21, 2014
Those Reloading Blues
I'm fairly new at reloading, having done only straight-wall pistol cartridges with mild loads on a single-stage press so far. I bought the press so I could afford to shoot my .44 Magnum, and I figured it would also work well for loading hunting and precision rifle ammo. This past weekend, I needed to go tinker with the roll crimp for my .38 Special recipe, and I figured what the heck, now that I've fired a few boxes of the Prvi factory ammo, I'll use the empty cases and dial in an initial batch of 9.3x62mm as well.
One thing I've discovered about reloading is that the ammo drought has extended to reloading components as well. I've got cases and projectiles, and was able to scrounge up 1000 WLRM primers, but powder is hard to find, especially locally. That's important, because when working up a load, I don't want to buy 8 lbs of a powder I might not end up using, and the combined hazmat and shipping fees are more than most 1lbs cans of powder cost. At those prices, I might as well just buy factory ammo. So after striking out on more common powders like Varget and RL15, and reading some various forum posts about people using it for the 9.3, I was rather happy when I found a single pound of Ramshot Big Game in a local store and forked over my money.
Now, as I mentioned, I'm new at reloading, and I don't consider myself anywhere near the level of experience to start going off into the weeds on load recipes. As I gain more experience, I might start doing some experimentation, but for now I stick to the book religiously, including component selection, measurements, etc. So imagine my surprise when I can't find any published data that uses Big Game in the 9.3 (Hornady lists TAC, and Barnes doesn't list any Ramshot powders for this cartridge), and only a few mentions of using Big Game specifically with Prvi cases and bullets (note: I don't plan to take Prvi bullets to Africa, but I do intend to use them for familiarization shooting, learning the initial ins and outs of reloading bottleneck rifle cartridges, and likely some whitetail hunting without breaking the bank on premium bullets. For the actual safari, I will be loading up the tried-and-true Barnes TTSX and either Barnes or Hornady solids.) My 'economy load' for practice and familiarization won't pan out if I can't find load data for it. So, off to the internet I go. And lo and behold, I found www.realguns.com had some data for Big Game with Prvi bullets. Awesome.
And so after I set up the RCBS neck sizing die and resize/measure the first sacrificial case, it's time to dial in the seating die. I'm hopeful that I can get everything zeroed in and start loading my initial batch. And before I seat a round, I take a look at the printout of the load data and I notice a little asterisk next to the COL data for the Prvi bullets. The data for this particular load has a COL of 3.305", 0.014" longer than the maximum COL in every factory book I've read (3.291"), and 0.030" longer than the COL of my factory Prvi ammo (3.275"). Spider sense... tingling. At this point, I put the dies away and go back to Google. Eventually I found someone using that particular recipe in a Ruger African with no issues, though he did back down the rather heavy powder charge and used non-magnum WLR primers. So, I emailed the Ramshot people to ask if they had any recipes for Big Game with Prvi bullets, but they don't.
So, for any of you more experienced reloaders out there, what would you suggest? Pick the data for a similar bullet, seat to normal COL, and start with a lower charge and work up? Keep looking for data for the exact components that I have?
One thing I've discovered about reloading is that the ammo drought has extended to reloading components as well. I've got cases and projectiles, and was able to scrounge up 1000 WLRM primers, but powder is hard to find, especially locally. That's important, because when working up a load, I don't want to buy 8 lbs of a powder I might not end up using, and the combined hazmat and shipping fees are more than most 1lbs cans of powder cost. At those prices, I might as well just buy factory ammo. So after striking out on more common powders like Varget and RL15, and reading some various forum posts about people using it for the 9.3, I was rather happy when I found a single pound of Ramshot Big Game in a local store and forked over my money.
Now, as I mentioned, I'm new at reloading, and I don't consider myself anywhere near the level of experience to start going off into the weeds on load recipes. As I gain more experience, I might start doing some experimentation, but for now I stick to the book religiously, including component selection, measurements, etc. So imagine my surprise when I can't find any published data that uses Big Game in the 9.3 (Hornady lists TAC, and Barnes doesn't list any Ramshot powders for this cartridge), and only a few mentions of using Big Game specifically with Prvi cases and bullets (note: I don't plan to take Prvi bullets to Africa, but I do intend to use them for familiarization shooting, learning the initial ins and outs of reloading bottleneck rifle cartridges, and likely some whitetail hunting without breaking the bank on premium bullets. For the actual safari, I will be loading up the tried-and-true Barnes TTSX and either Barnes or Hornady solids.) My 'economy load' for practice and familiarization won't pan out if I can't find load data for it. So, off to the internet I go. And lo and behold, I found www.realguns.com had some data for Big Game with Prvi bullets. Awesome.
And so after I set up the RCBS neck sizing die and resize/measure the first sacrificial case, it's time to dial in the seating die. I'm hopeful that I can get everything zeroed in and start loading my initial batch. And before I seat a round, I take a look at the printout of the load data and I notice a little asterisk next to the COL data for the Prvi bullets. The data for this particular load has a COL of 3.305", 0.014" longer than the maximum COL in every factory book I've read (3.291"), and 0.030" longer than the COL of my factory Prvi ammo (3.275"). Spider sense... tingling. At this point, I put the dies away and go back to Google. Eventually I found someone using that particular recipe in a Ruger African with no issues, though he did back down the rather heavy powder charge and used non-magnum WLR primers. So, I emailed the Ramshot people to ask if they had any recipes for Big Game with Prvi bullets, but they don't.
So, for any of you more experienced reloaders out there, what would you suggest? Pick the data for a similar bullet, seat to normal COL, and start with a lower charge and work up? Keep looking for data for the exact components that I have?
Subscribe to:
Posts (Atom)

